November 25, 2022
How-to-Install-a-Router-Linksys

How to Install a Router Linksys

How to Install a Router Linksys? By inserting the Linksys router’s installation CD or manually configuring the router’s settings, you can set up your router with a Cable Internet Service.  The Linksys Connect Software is recommended for use with Linksys Wi-Fi Routers and Linksys Smart Wi-Fi Routers.  This tutorial will show you how to set up Linksys Smart Wi-Fi Routers using Smart Setup.

A QUICK TIP: If you are unsure about the type of Internet connection you have, get in touch with your Internet Service Provider (ISP).

Linksys routers can be set up using the computer that is registered to your ISP by performing four (4) procedures:

  1. Connecting to the Internet and verifying its status
  2. Interconnecting devices
  3.  LEDs on the router should be checked
  4. Setting up a Linksys router for Cable Internet connection

 QUICK TIP: To reconfigure an older router, reset it to factory defaults.  Hold down the Reset button on your router for 10 seconds to do this.  Most routers have a Reset button at the back.


Connect the Ethernet cable from the computer to the Cable modem to verify the Internet connection is active.  You may proceed to the next step if your computer is getting an Internet connection.  Otherwise, you should contact your Internet service provider.

It is important to note that some Cable modems have their USB ports configured by the ISP to provide your computer with Internet access.  You will not be able to use an Ethernet connection if the physical connection is through a USB port.  Check with your ISP to make sure the modem’s Ethernet port is configured.

A device’s connection to another     

How to Install a Router Linksys. Follow the following steps to know. We are using the Linksys E4200 in this example.

Step 1:

Cable modems should be connected to the router’s WAN or Internet port.

Step 2:

Any of the router’s numbered ports (1, 2, 3 or 4) can be used to connect a computer.  You must first connect your wireless computer to an Ethernet cable if you are using one.

A computer is attached to port number 2 in this example.

Step 3:

Your router’s power adapter should be connected to a power outlet.

Checking the router’s LEDs

Verify that the router’s front panel is lit up after connecting the devices.  Connect the Ethernet cables to the ports that are lit by the corresponding lights.

Also check: Which Router is Best for Vpn

Linksys router configuration for cable internet

Step 1:

Setup your router using the web-based setup page.  Use any of the following web browsers to browse the web: Internet Explorer®, Mozilla Firefox® or Safari®.  In the address bar, type “192.168.1.1” and press [Enter].

Step 2:

Then, you’ll need to enter your login information.  The User name field should remain blank, and the Password field should be filled in with “admin” and clicked OK.

If you receive an error message after entering your router’s password, the password you entered was incorrect.  You may need to enter the correct password again after opening the router’s web-based setup.  You can reset your router to its factory settings if you have forgotten or lost its password. Click here to learn how.

Step 3:

Click the MAC Address Clone button under the Setup tab.

Media Access Control (MAC) addresses are unique identifiers assigned to each computer’s network adapter.  A cable ISP uses this to authenticate subscribers so they can connect to the Internet.

You must therefore enable the MAC Address Clone feature on your Linksys router for it to work with your ISP.  Thus, your ISP will be able to identify your router as the computer that has the registered MAC address.

Step 4:

Choosing Enabled and clicking Clone My PC’s MAC will do.

Step 5:

The settings will be saved when you click Save.

Establishing a connection to the Internet

The Internet status should be active once the MAC Address Clone feature is enabled.  Checking the status of the Internet Connection can be accomplished as follows.

Make certain that Automatic Configuration – DHCP is selected as the Internet Connection Type.

Step 1:

Select Status from the menu.

Step 2:

The IP address of the Internet should be checked.  If it contains numbers, it indicates that the router is properly configured.  Click on Release IP Address and then Renew IP Address if the Internet IP Address is showing 0.0.0.0.

The DHCP release and renewal buttons on the Wireless-B and Wireless-G routers must be clicked. Internet access should be available now.  You should power cycle the computer, router, and modem if it doesn’t.

You should be cautious when power cycling a cable modem.  Cable TV and phone services are bundled with cable modems.  It is also possible for cable modems to have backup batteries that prevent them from turning off even if the power adapter is disconnected.  You can power cycle your modem by consulting your ISP.

In order to complete a powercycle:

Step 1:

Shut down the modem.

Step 2:

You can shut down your computer after unplugging the router’s power adapter.

Step 3:

Wait for the modem’s lights to go steady after it is turned on.

Step 4:

The router needs to be turned on first, then the computer needs to be turned on after the router lights are steady. Hopefully, now you have access to the Internet.  Your ISP may need to reconfigure the modem if you cannot go online.

Now you know How to Install a Router Linksys!

Leave a Reply

Your email address will not be published. Required fields are marked *